The effectiveness of the APQP process is measured on its ability to meet the goal of successful launches. https://dana.livesource.com/. Rev Date 1/3/2019 Page 2 Safe Launch Process.xls. Supplier Quality Requirements Manual Document: PH-SQRM, Mar-08 Page 6 of 25 Wages and Benefits – Suppliers shall compensate workers in accordance with local, state, and federal laws/regulations in the country of origin. Any missing and / or questions related to the understanding of the intent of Dana Engineering Standards shall be communicated to your Supply Chain Management Representative prior to initiating supply to Dana. “Non-conforming Material” was “Corrective Action” – section re-written and re-formatted. Dana representatives shall be permitted to review the submitted root cause validation. It encompasses a thorough review of a supplier’s capacity, special characteristic capability, control and documentation to ensure the resultant product is in complete compliance to all Dana drawing, specification requirements and the quoted contractual volume. If Dana defines special controls for certain products with statutory and regulatory requirements, suppliers shall ensure they are implemented and maintained as defined, including throughout their supply base. In addition, the supplier must meet all other requirements of this manual as well as any additional requirements stated on the Purchase Order or PR provided drawings. All tools must be permanently marked as specified by the Buyer. Adient Global Supplier Standards Manual - Metal Prototype Weld Fixture Design Requirements May 2013 Adient Global Supplier Standards Manual - Metal Prototype Welding Operator Qualifications and Procedures May 2013 http://www.dana.com/corporate-pages/standards-of-business-conduct, All Production suppliers must be registered to Dana1Source in order to gather your critical contact and organizational data. 6.11 Supplier Improvement Process: Suppliers with ineffective problem solving processes, multiple high quantity rejections and/or multiple quality incidents will be required to participate in a Supplier Development Improvement Process, the elements of which will be determined by Dana in its reasonable discretion. This Manual is an integral part of each purchasing agreement between Continental and Supplier and states binding requirements for Supplier. Mixed parts will be defined as the number of wrong parts found in each correctly labeled container. Dana Global Casting Quality Requirements – Revised paragraphs e) & f) in the Casting Development Requirements section. 4.1 Quality System: Dana’s requirement standard for our supply base is registration to the latest edition of IATF 16949 or ISO 9001. Dana does not pay for profit margin to a supplier or sub-supplier for tooling. Quality Requirements for Suppliers in respect to all active contracts and purchase orders. No production shipments shall begin until you have received the approved PSW from the receiving Dana facility. For Asia Pacific Programs forward submissions to supplierdevelopmentap@dana.com. When required by the Dana Product Group one additional sample from the initial production must be x-rayed and documented evidence supplied with the PPAP Submission that shows the results correlate with all development modeling, Pre-PPAP sectioning and analysis or the PPAP will be rejected. Lvl 17 Printed Copies are Uncontrolled GI-SPR-10.1 Date: 2-DEC-2020 2.0 Scope This manual applies to all Auria production, non-production, and service suppliers globally. Key system factors evaluated include quality, safety, process, logistics / packaging, APQP, design, change management, people, leadership, cost and special processes modules critical to producing Dana product. Dana will pay suppliers the actual and eligible cost of making the tooling. It establishes the minimum requirements for all direct material suppliers of production materials and processing services purchased by … http://www.dana.com/corporate-pages/standards-of-business-conduct. 3.1 APQP Workbook to Supplier: The Buyer or designated Product Group representative will communicate the required APQP Workbook to your organization. \C"`��.&��v0������H���`�-M��P���sL� ήƐ�яٵ�j|y Unless otherwise specified in your supply agreement, purchase order, the Director of Dana Supplier Development or the Dana receiving facility Quality Manager the PPAP shall include a Run@Rate analysis of at least 8 hours during which there needs to be representation of required change overs and unplanned downtime. endobj �#5�­��Ә�#���a(e8�p_���F�YDs䒹�-�BDs�Y5����"�#��:_�,�;2���)DtG&m~��r��̦�r SUPPLIER REQUIREMENTS MANUAL Revision: 05/15/2016 5 1.0 Introduction SL TN’s Procurement group is the supplier’s first line of communication and permission-granting authority whenever components or services are contracted and are provided to the company. Dana will monitor the progress based on milestones on the planned activities. Our business relationship will be based on the requirements set forth in this manual as well as the contract or purchase order terms and conditions that are specific to your transaction(s) with Dana. Supplier Quality Requirements Manual Document: PH-SQRM, Mar-08 Page 6 of 25 Wages and Benefits – Suppliers shall compensate workers in accordance with local, state, and federal laws/regulations in the country of origin. Component/service parts suppliers currently not certified: Suppliers whose Quality Performance, as shown in our Supplier Performance Feedback System, conforms to Dana’s specified requirements will be given the right to complete and submit a Self - assessment. The inspection report shall be shipped with the prototype samples. This evidence shall be included in the SCAR response. Please contact your Supply Chain Management Representative if you have any questions regarding these requirements. Exception: if the deviation becomes a Dana print change then none of the deviated parts will be considered discrepant.